Western PRO-FLO 2 Bedienungshandbuch Seite 1

June 15, 2003Lit. No. 94417PRO-FLO™ 2TAILGATE SPREADEROwner’s ManualThis manual supersedes all editions with an earlier date.This manual is for WESTER

June 15, 2003 6 Lit. No. 94417/944186. Position the tabs of the hopper assembly over thetop of the mount assembly, and lower.7. Allow the hopper assem

Lit. No. 94417/94418 7 June 15, 2003Under-Frame Mount1. Install the secondary frame into the subframe.2. Insert a hitch pin on each side, and secure w

June 15, 2003 8 Lit. No. 94417/944185. Insert a hold-down pin on each side and secure withhairpin cotter pin.6. Connect the spreader wiring harness to

Lit. No. 94417/94418 9 June 15, 2003OPERATING THE SPREADERDriving and Spreading on Snow and IceFollow your vehicle owner’s manual instructions fordriv

June 15, 2003 10 Lit. No. 94417/94418Adjusting the Gates and the DeflectorSpread pattern, pattern width, and the amount ofmaterial dispensed are depen

Lit. No. 94417/94418 11 June 15, 2003STARTBLASTONOFFSPINNERMIN MAX12345679SPEED8PENDINGPATENTPower SwitchUsed to start andstop the spinner(Emergency S

June 15, 2003 12 Lit. No. 94417/94418BLASTONOFFSPINNEROn/Off Control SwitchUsed to start and stopthe spinner.(Emergency Stop when required)Spinner In

Lit. No. 94417/94418 13 June 15, 2003REMOVING THE SPREADERIn-Bed MountNOTE: Empty the hopper before removing thespreader.1. Disconnect the spreader wi

June 15, 2003 14 Lit. No. 94417/94418REMOVING THE SPREADERUnder-Frame MountNOTE: Empty the hopper before removing thespreader.1. Disconnect the spread

Lit. No. 94417/94418 15 June 15, 2003RECEIVER HITCHSafetyImportant Information on TowingMake sure all operators of your equipment read andunderstand t

June 15, 2003 16 Lit. No. 94417/94418RECEIVER HITCHTire InflationCheck often. Follow tow vehicle and trailermanufacturer’s recommendations. Improper t

Lit. No. 94417/94418 17 June 15, 2003To keep your spreader running smoothly, observe thefollowing recommendations:• Lubricate grease fittings after ea

June 15, 2003 18 Lit. No. 94417/94418MAINTENANCEAfter each use• Wash out hopper and rinse off all external surfaces.• Wash out the secondary frame slo

Lit. No. 94417/94418 19 June 15, 2003Cab ControlWhite ConnectorRed Connector8 Ga. Red8 Ga. Red14 Ga. Red10 Ga. Red14 Ga. Black8 Ga. Black14 Ga. Orang

June 15, 2003 20 Lit. No. 94417/94418Cab ControlWhite ConnectorRed Connector8 Ga. Red8 Ga. Red10 Amp Fuse14 Ga. Red8 Ga. Red14 Ga. Black8 Ga. Black14

Lit. No. 94417/94418 21 June 15, 2003TROUBLESHOOTING GUIDEPROBLEM POSSIBLE CAUSE SUGGESTED SOLUTIONIce control material not flowing1. Bridging of mate

June 15, 2003 22 Lit. No. 94417/94418TROUBLESHOOTING GUIDEPROBLEM POSSIBLE CAUSE SUGGESTED SOLUTIONIce control material not flowing1. Bridging of mate

Lit. No. 94417/94418 23 June 15, 2003TROUBLESHOOTING GUIDEPROBLEM POSSIBLE CAUSE SUGGESTED SOULUTIONIce control material not flowing1. Bridging of mat

Copyright© 2003 Douglas Dynamics, L.L.C. All rights reserved. This material may not be reproduced or copied, in whole or in part, in any printed,mecha

June 15, 2003 26 Lit. No. 94417/94418TABLE OF CONTENTSPREFACE ... 1Before You Begin ..

Lit. No. 94417/94418 1 June 15, 2003PREFACEThis manual has been prepared to acquaint you with thesafety information, operation and maintenance of your

June 15, 2003 2 Lit. No. 94417/94418SAFETY INFORMATIONBefore You Begin• Park the vehicle on a level surface, place shift leverin PARK or NEUTRAL and s

Lit. No. 94417/94418 3 June 15, 2003SAFETY INFORMATIONWarning/CautionLabelWarning/CautionLabelPlease become familiar with the Warningand Caution label

June 15, 2003 4 Lit. No. 94417/94418371 lb.950 lb.Sand = 95 lb./ft.³Salt = 40 lb./ft.³400 lb.156 lb.10 ft.³3.9 ft.³10 ft.³3.9 ft.³Salt = 40 lb./ft.³ (

Lit. No. 94417/94418 5 June 15, 2003MOUNTING THE SPREADERIn-Bed Mount1. Remove the tailgate from the vehicle.2. Place the mount assembly into the bed